IP65 Panel PC Selection Guide

IP65 Panel PC Selection Guide: Platform, Size and Sealing

An IP65 panel PC is a sealed computer with a touch screen, mounted into a machine, a wall or an enclosure. Three decisions determine whether you get the right unit: the computing platform (x86 or ARM), the size and mounting geometry, and what "IP65" actually covers. Get the platform wrong and the software will not run; get the sealing wrong and the unit fogs up in its first winter. This guide walks through all three.

1. x86 or ARM: the decision that is not about performance

Buyers usually frame this as a speed question. In practice it is a software and lifecycle question, and the answer is decided by what already exists at the machine.

Intel x86 (Celeron, i3, i5, i7)ARM (RK3566, RK3568, RK3399)
Operating systemWindows 10/11, Linux, some industrial RTOSAndroid 11/12, embedded Linux
Existing softwareRuns the Windows HMI or SCADA client you already haveNeeds an Android or Linux build of that software
Power draw35–120 W depending on CPU10–25 W
HeatNeeds a heatsink or fan; fan means an openingOften fanless, easier to seal completely
Real-time controlCan drive PLCs and motion over PCIe/PCI cardsBetter at media, not at deterministic I/O
CostHigher, especially i5/i7Lower, roughly 40–60% of an i5 unit
Lifespan riskCPU generations retire; plan for a 5-year supplyLonger module availability, but Android API level matters

The practical rule:

  • Choose x86 when the machine already runs Windows software you cannot recompile, when you need PCIe expansion, or when the unit must join a domain. This is the majority of machine-retrofit projects.
  • Choose ARM when the display only shows content, runs a kiosk browser, or the application is a purpose-built Android app. It is cheaper, cooler, and easier to seal because there is no fan.
The trap: a fanless x86 unit is not automatically IP65. Fanless removes one opening, but the rear panel still needs a sealed cable entry and a sealed housing. Ask for the IP rating of the complete assembly, not the bare board enclosure.

2. What IP65 actually covers on a panel PC

This is where most specification mistakes happen. Three arrangements are sold under the same "IP65" label:

ArrangementWhat is sealedWhere it is acceptable
Front onlyThe front bezel and touch face; the rear chassis is open or ventilatedRecessed into a clean indoor cabinet; the machine itself protects the rear
Front and rearThe whole housing sealed, cables through waterproof glandsWash-down areas, food processing, outdoor cabinets
Front only, with a sealed rear boxPanel PC sealed at the front; the customer's enclosure seals the restOEM machines where the customer owns the cabinet design

Ask the supplier for the IP test report and check which faces were tested. A unit rated IP65 on the front face only will fail in a wash-down area within months, because water runs down the rear and into the USB and RJ45 ports.

The condensation problem in sealed housings

A fully sealed panel PC has no airflow. In a cold room or an outdoor cabinet, the cover glass drops below the dew point overnight, and moisture inside the housing condenses on the inside of the glass. The result is a screen that fogs from the inside and cannot be wiped clear — a failure that is invisible in the datasheet and obvious to the operator.

The fix is optical bonding: the air gap between cover glass and LCD is filled with adhesive, so there is no volume for moisture to condense in. On a sealed IP65 unit, bonding is not a cosmetic upgrade — it is what makes the sealing strategy work. See how the bonding process works.

3. Size, cut-out and mounting geometry

Panel PCs are mounted three ways, and the drawing you need differs for each:

  • Front-mount into a cut-out. The unit clamps from behind, and the front bezel sits flush with the machine face. You need the cut-out dimensions and the clamp depth, not the outline size. Allow 10–15 mm clearance behind the panel for the clamps and cable bend radius.
  • VESA wall or arm mount. The unit hangs on a 75×75, 100×100, 200×200 or 400×400 pattern depending on size. Check that the VESA pattern clears the cable exit — on small units it often does not.
  • Standalone enclosure. The unit sits in its own sealed box with glands for power and network. This is the only arrangement where the PC's own rear sealing does all the work.
Screen sizeTypical useMounting note
10.1–15.6 inchMachine HMI, single-operator stationCut-out or VESA 75/100; light enough for a swing arm
21.5 inchMachine centre, control cabinet doorCut-out most common; check door thickness for clamp depth
32 inch and upControl room, dispatch wall, production overviewVESA 200×300 or larger; wall structure must carry 25 kg+

4. Interfaces: match the machine, not the datasheet

Count the ports the machine actually needs before choosing a model:

  • Network — one RJ45 is standard; two if the unit bridges IT and OT networks.
  • Serial — RS-232/485 is still how most PLCs and drives talk. Many panel PCs drop it, and a USB-to-serial adapter inside a sealed box is a bad answer.
  • USB — at least two, one of them reachable from outside the cabinet for a keyboard or a USB stick during commissioning.
  • Video out — HDMI out to a second screen is common on control-room units, rare on machine HMIs.
  • Power — wide-voltage DC input (12–36 V) survives the dips that a machine's 24 V rail produces; a fixed 12 V input does not.

5. Matching the unit to the job

Our IP65 range splits by what is behind the glass:

6. The specification checklist

  1. List the software the unit must run, and the OS it runs on. That decides x86 vs ARM before anything else.
  2. Decide which faces need IP65: front only, or front and rear. Write it into the PO.
  3. Get the cut-out drawing and check clamp depth against your panel thickness.
  4. Count the ports, including serial, and confirm they are accessible after installation.
  5. Specify bonding if the unit is fully sealed or works in a cold/humid environment.
  6. Check the power input range against the machine's supply, including dips.
  7. Ask about fan and filter replacement if the unit is actively cooled — a filter that nobody changes is a failure waiting to happen.

Send us the machine drawing and the software requirement. We will tell you which platform fits, whether you need front-only or full IP65, and whether bonding is required for your environment — usually within one working day.

Ask for a panel PC recommendation →

Related reading

Leave Your Message
  • captcha

 
Leave a message